Skip to main contentSkip to navigationSkip to footer

ALBA Synchrotron

  • Careers
  • ALBA II
  • Transparency
English.
UsersIndustryInstrumentsPublicScienceAbout
en
  • English
  • Español
  • Català
Log in
  • FacebookTwitterWhatsappLinkedin
  • Contact
Home
/
Instruments
/
Beamlines
/
BL06 - XAIRA
/
Sample environments & preparation
Sample environments

Sample changer

The automatic sample changer of the beamline is an ISARA2 from Irelec. The maximum capacity of the sample storage Dewar is 464 samples (29 pucks).

Caps/Vials

Only SPINE caps/vials are supported. In the case of the double gripper (Unipuck) the use of SPINE caps is mandatory (Molecular dimensions, Mitegen or Hampton SPINE caps) (see figure below). The use of other standards will cause serious collisions.

Pin length

22 mm pin length is strongly recommended, if you bring longer or shorter pins, make sure to bring an empty pin (sample) to test the position of the cryostream before mounting your samples. Any common brand of pins is allowed (Hampton, MD, etc).

Cassettes (pucks)

16-sample UNIPUCK cassettes (pucks/baskets) are supported for automatic mounting in the ISARA2 sample changer

Serial Crystallography (Comming by the end of 2025)

Back up system

External hard disk drive (preferred). Please bring your own external hard disk drive.
SFTP may also be possible depending on amount of data.

Download your results obtained with the automated data processing pipeline through Data portal: https://data.cells.es

Typical software for data processing is available. Automatic processing with FastDP, autoPROC pipeline and XIA2.

Wet laboratory

A wet laboratory is at your disposal which is close to the beamline to facilitate standard crystal manipulation and preparation. A Mosquito LCP for general crystal screening, a Dragonfly for setting up optimizations and a Formulatrix imager allowing remote visualization of the crystallization plates are available, as well as a Crystal Shifter for fast crystal freezing and automatic sample tracking.

Before your experiment

Continous access to XAIRA

Continuous Access is already implemented, please check the user call page.

  • A maximum of 6 shifts will be allocated per proposal
  • (For Spanish Institutions only) Maximum 2 visiting users for 3 shifts or 1 visiting user for 1-2 shifts is funded.per visit
  • The dewar shipment is funded for groups within the EU

Remote Access

This option allows users running the experiment remotely from their home institution via an NX session. Data collection can be fully remote avoiding the need to travel to ALBA, in this case the local contact will load the pucks into the ISARA2 dewar during working hours. Floor coordinators will give support and exchange pucks during the night shift (phone number: ask LC). A phone number must be provided to the LC to keep in touch with the user during the experiment. In case you do not remember your login/password, the LC will provide it to allow connection to NX.

REQUIREMENTS AND CONNECTION PROCEDURE: Follow the remote access user guide

DATA DOWNLOAD: See the FTP instructions in this page (section 4).

Dewar Transport instructions

Follow the DEWAR SHIPPING AND MANAGEMENT section 7

Running your experiment

Local contact during experiment

Your local contact will have the beamline ready at 9:30 h. S/He will be on site between 9:30 h-18:30 h. After 18:30 h, s/he will be reachable by cell phone until 22 h, and will assist you remotely or presentially at the beamline if required. Floor coordinators are available on weekdays from 15h to 7h and 24 hours on weekends and bank holidays.

How to retrieve your data

  • Via a web browser (Data Portal, preferred).The results obtained with the automated data processing pipeline can be downloaded at home through the Data Portal platform (https://data.cells.es) using your user office account to log in.
  • External Drive (preferred for RAW data backup). The preferred way to take the data away with you is by the use of an external drive (mounted on Linux or Windows) on site on either the USB2 or the USB3 port. You will find precise instructions on how to do this at the beamline. Supported formats FAT32 and NTFS.
  • SFTP server for remote data access. ALBA provides remote access to the experiment data using the SFTP protocol. All the information is available at section 4 of this page. Note that data storage is only guaranteed for 6 months after the day of your experiment, although the data is usually stored for some time longer.
Report publications & experimental reports
ImportantInformation for Users

Should you author or have a publication accepted which contains data, totally or partially, from experiments conducted at an ALBA facility, please report it to us using this form and send it to the ALBA User Office. Note also that BAG allocation requires the submission of an experimental report, more information can be found here.

Authors should use the following text in the acknowledgement section: “These experiments were performed at BL-06 XAIRA beamline at ALBA Synchrotron Light Facility with the collaboration of ALBA staff.”

Your collaboration is vital to track the ALBA data production and enable us to be in a better position to serve your future experiments.

Help us improve

Was this page useful to you?

Alba Synchrotron
Consortium for the Construction, Equipping and Exploitation of the Synchrotron Light Source (CELLS)

Synchrotron light source in Spain for discovering the secrets of life sciences, materials for energy, environment, nanomaterials, cultural heritage and many more.

Carrer de la Llum 2-26 08290 Cerdanyola del Vallès, Barcelona, Spain

How to arrive+34 93 592 43 00

Subscribe to our newsletterSubscribe

FacebookXYouTubeInstagramLinkedIn

  • Accessibility
  • Contact
  • Legal notice
  • Privacy policy
  • Cookies policy
  • Site map
© 2025 CELLS

Project developed byeCityclic.